<pgMar> (Page Margins)

Specifies the distance (in twentieths of a point) between the bottom of the text margins for the main document and the bottom of the page for all pages in this section.

If the value of @bottom is non-negative, then the text will be placed at the greater of:

• The value of @bottom

• The extent of the footer text

<w:pgMar ... w:bottom="720"
  w:footer="1440"/>

This fragment specifies that the footer shall start 1440 twentieths of a point from the bottom of the page, but the main document story shall start 720 twentieths of a point from the bottom of the page. Since the footer extent is guaranteed to be greater in this case, the bottom text extent ends at the top of the footer region. ]

A negative value indicates that the contents of the main document shall be measured from the bottom of the page extent regardless of the footer for that document, and therefore shall overlap the footer text.

<w:pgMar ... w:bottom="-720"
  w:footer="1440"/>

This fragment specifies that the footer shall start 1440 twentieths of a point from the bottom of the page, and the main document story shall start 720 twentieths of a point from the bottom of the page. Since the value of @bottom is negative in this case, the bottom text extent starts one-half of an inch from the bottom of the page and overlaps any footer text. ]

The possible values for this attribute are defined by the ST_SignedTwipsMeasure simple type (§2.18.88).

Specifies the distance (in twentieths of a point) from the bottom edge of the page to the bottom edge of the footer.

To specify this boundary, the following page margins must specified in the WordprocessingML:

<w:pgMar … w:footer="1440"/>

This fragment specifies that the footer shall start 1440 twentieths of a point from the bottom of the page. ]

The possible values for this attribute are defined by the ST_TwipsMeasure simple type (§2.18.105).

Specifies the page gutter for each page in the current section.

The page gutter defines the amount of extra space added to the specified margin, above any existing margin values. [: This setting is typically used when a document is being created for binding, in order to ensure that the resulting margins are present after the binding gutter is consumed by the printed matter binding. ]

To specify this condition, a user could simply use a left margin of 1.5 inches, which would be lost if the margins are later changed, or could specify a one-half inch gutters follows in the WordprocessingML:

<w:pgMar … w:gutter="720"/>

This fragment specifies that the gutter shall span 720 twentieths of a point, after which any margin value shall be added. ]

The possible values for this attribute are defined by the ST_TwipsMeasure simple type (§2.18.105).

Specifies the distance (in twentieths of a point) from the top edge of the page to the top edge of the header.

<w:pgMar … w:header="2880"/>

This fragment specifies that the header shall start 2880 twentieths of a point from the top of the page. ]

The possible values for this attribute are defined by the ST_TwipsMeasure simple type (§2.18.105).

Specifies the distance (in twentieths of a point) between the left edge of the page and the left edge of the text extents for this document.

<w:pgMar … w:left="2880"/>

This fragment specifies that the left margin shall span 2880 twentieths of a point from the left edge of the page. ]

The possible values for this attribute are defined by the ST_TwipsMeasure simple type (§2.18.105).

Specifies the distance (in twentieths of a point) between the right edge of the page and the right edge of the text extents for this document.

To specify this boundary, the following page margins must specified in the WordprocessingML:

<w:pgMar … w:right="1440"/>

This fragment specifies that the right margin shall span 1440 twentieths of a point from the right edge of the page. ]

The possible values for this attribute are defined by the ST_TwipsMeasure simple type (§2.18.105).